How to Replace a Kia Sportage Replacement Key

The key of many Kia models comes with a keyless entry system built into. This key typically resembles an remote control, and is able to be replaced with a fresh one from a Kia dealer or locksmith.

Key fobs may stop working due to a variety of reasons, such as the battery being dead, worn-out buttons, signal interference or water damage. Here are some suggestions to assist you in getting your Kia sportage replacement key fob kia key to work again.

How do you replace the remote key or smartkey

It doesn't matter if your Kia comes with an intelligent key, remote key, push to start key or a standard non-transponder key made of metal The battery inside these keys will eventually need replacement. This is especially when the car displays a message that the remote or smart key is not powered by the battery.

It's a fairly simple procedure. To replace the battery in the keyfob take out your mechanical key from the slit at the back of the fob. Then, pull the cover open. Inside the key fob, there will be the small screw that holds the battery in the correct position. Take out the old battery by detaching the screw with a small screwdriver. Install the new battery and close the cut on the key fob.

Once the key fob has a fresh battery, test it by pressing the locks and unlock buttons. You're in good shape when the doors lock or unlock as expected. You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or when you need to go on errands around Brandon.

Note: Some key fobs (transponder chip or smart keys) may need to have their programming completed. This requires a specific programming machine that only the dealer or automotive locksmith can access. Other keys (non-transponder metal keys) don't require programming. If your keys need to be programmed again, you will need to be aware of the number printed on the tag that identifies the key and save the number in a secure place.

How do you replace a battery?

If the Kia key fob doesn't respond when you press the lock/unlock button, it is most likely that the battery is insufficient. A low battery may cause other issues, like the check engine light appearing or the engine not turning correctly. Fortunately replacing the key fob battery is a fairly simple DIY project that requires just a few basic tools.

Before you begin, make sure that your vehicle is off and all doors are closed. Locate the small plastic piece at the bottom of your key fob, and gently jiggle it until the metal key is released. Then, you can insert this key into the handle on the door of your driver to open your car.

To replace the battery on the key fob, you must remove the cover on the rear. Utilize a plastic plier tool to open the latch that holds the black negative cable. Remove the old battery and then align the replacement battery in a way that its "+" side faces you, and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place and avoid excessive force to avoid damaging or bending the contacts on the metal.

After the new battery has been installed after which you turn the key fob off and then turn it on in the ignition until the door locks. Then, test your Kia key fob to check if it is working properly again.

How do you replace a keyless keys

You may have either the standard keyfob or Smart Key based upon the model of Kia Sportage. The smart key features an embedded mechanical key blade while the standard key fob does not. Both kinds of key fobs contain a battery inside them that will eventually need to be replaced. Fortunately, this is an easy process that will take about two minutes.

Before you get started it is essential to ensure that you're on a flat surface with enough lighting and that your Kia is turned off. Also, remember that there are small parts inside the fob which could be removed if not cautious.

The first step is to find the small release button on the backside of the fob. It's either a circular button or a rectangular slot. You can open the key fob by pressing the button.

After the key fob has been opened, take out the battery that was in it. The new battery should be a CR-2032, and can be purchased online or at a local auto parts store. After you've finished, you should be able to lock and unlock your car with your key fob even if the engine isn't running!

How do you replace the mechanical key?

The Kia keyfob is an excellent convenience, allowing us to lock or unlock our car by simply pressing a button. Like any other device, the Lost Kia Car Key key fob might have issues. Luckily, there are steps that can be taken to resolve these issues and ensure that our key fobs are in good working condition for the long run.

A dead or low-quality battery is one of the most frequent problems. This can cause the device to stop working completely or to work intermittently. If this is the case then try replacing the battery with a fresh new one.

If this doesn't solve the issue, try using the flathead screwdriver that is standard to wedge the plastic casing of the fob open. Be sure not to damage any internal components or scratch the plastic. After opening, carefully remove the battery that was removed and replace it with a brand new one.

Close and open the door using the mechanical key. (Every kia fob comes with a spare mechanical key which will fit into the slot). Test the key fob to verify that it's working properly. If the device isn't working, contact an expert locksmith or dealer to help solve the problem. Make sure they make you an emergency key that functions across all trunk and door cylinders, to prevent lockouts in the future.