How to Replace a Kia Sportage Replacement Key

The key on many Kia models comes with an entry system that is keyless in. The key functions like the remote control, and is exchangeable by a Kia dealer.

Key fobs are prone to malfunction due to a variety of reasons, including an empty coin battery worn buttons, water damage, signal interference and a malfunctioning receiver module. Here are some suggestions on how to get your Kia Sportage replacement key to function again.

How do you replace a remote key or a smartkey?

No matter if your Kia is equipped with an intelligent key, remote key push-to-start key, or a regular non-transponder steel key The battery inside these keys will eventually need replacement. This is especially when your car displays a message telling you that the remote or smart keys are not powered by batteries.

It's a simple process. To replace the battery of the key fob, remove the mechanical key from the slit in the back of the key fob and remove the cover. Inside the key fob there will be tiny screws that hold the battery in its place. Take out the old battery by unscrewing the screw using a small screwdriver. Install the new battery and close the slit on the key fob.

When the key fob is equipped with new batteries Test it by pressing the locks and unlock buttons. If the doors lock and unlock exactly as you expect, then you're in good shape! You can now utilize the hands-free feature to lock and unlock your Kia Picanto Key Fob Replacement whenever your fingers become cold or you need to run errands around Brandon.

Note: Some key fobs could need to be programmed (transponder chips or smart keys). This requires a computer, which is only available to the locksmith who works for the automotive dealer. Other keys (non transponder keys made of steel) do not require programming. If you need to reprogramme your key, you'll need record the key code number on the key code tag.

How do you replace a dead battery?

If the Kia key fob is unable to respond to pressing the lock/unlock button, it is likely that the battery is insufficient. A weak battery could cause other issues, such as the check engine light flashing or the engine not working correctly. Fortunately, replacing the battery on the key fob is a relatively easy DIY project that requires just a few tools.

Before you begin the process before beginning the process, ensure that your vehicle is turned off and that all doors are closed. Locate the small metal or plastic piece on the bottom of your key fob and move it until a metal key slips out. You can then insert this key into the handle of the door for the driver to unlock your car.

To replace the key fob battery, take off the rear cover and use a plastic pry bar tool to loosen the latch holding the black negative battery cable. Remove the old battery, and then align the new one to ensure that the "+" positive side is facing you, while the "-" negative side is facing the fob's metal electrical contacts. Avoid using excessive force when pushing the new CR2032 into place to avoid damaging or breaking the metal contacts.

After installing the new battery and turning the key fob off and on in the ignition until the door locks cycle. You can then test the Kia's key fob once more to ensure it's working properly.

How can you replace the smart key

You could have a standard keyfob or a Smart Key, based on the model of kia key fob replacement Sportage. The smart key has an embedded mechanical key blade while the standard key fob does not. Both kinds of key fobs contain batteries that will eventually have to be replaced. Luckily, this is quite simple and takes just two minutes.

Make sure to shut off your Kia and be on a level, well-lit surface before you begin. Remember that the fob can contain small pieces that could be thrown off should you not be careful.

The small release button is located on the lower backside. It's either a circular button or a rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob open and you are able to remove the old battery, and replace it. The new battery is C2032, and can be bought on the internet or at your local auto parts store. After installation, you should be able to lock or unlock your car using your key fob, even if your engine isn't running!

How do I replace the mechanical key?

The Kia key fob is a great option that lets us lock and unlock our car with the press of an button. Like all devices, the Kia key fob can occasionally have problems. There are solutions to solve these issues and keep your key fobs working for a long time.

One of the most common problems is a dead or dead battery. This can cause the fob to stop working entirely or even to stop working intermittently. If this is the case try replacing the battery with a new one.

If this doesn't resolve the issue, try using a standard flathead screwdriver to open the fob's plastic casing. Be careful not damage any internal components, or scratch the plastic. When the battery is open, carefully take off the battery that was removed and replace it with a new one.

Close and open the door with the mechanical key. (Every kia fob comes with an emergency mechanical key that fits into the slot). Test the key fob and ensure that it's working properly. Contact a dealer or a locksmith to solve the issue when the fob still is not working. To avoid lockouts in the future, make sure you get an emergency key that will work on all door and trunk cylinders.