Repairs to uPVC Windows

uPVC is an excellent choice for modern homes. They are long-lasting, durable and easy to maintain. They don't get rotten or rusty like timber and aluminum.

Regularly cleaning and lubricating UPVC windows and doors is essential. This will reduce unnecessary repair costs and improve energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause significant damage to your home and may even be fatal. It is essential to take the time to make sure that you're doing everything you can to keep your windows in good shape.

Single-pane windows are relatively easy to replace and typically fit into frames that were previously in use very easily. However If you have double pane windows that are secured by internal beading, UPVC Window Repairs it'll be more difficult to get rid of the old panes and put in new ones. In this instance you'll need to source some plastic spacers to help the new pane to fit correctly into the window frame.

Wearing protective eyewear and thick gloves is a must if you plan to remove the glass by yourself. It is also recommended to lay down a drop cloth before you start working on the glass so that any shards fall onto the cloth rather than on the floor, where they could be trodden under and cause further damage.

Once the glass has been removed from the window, it's best to seal the gap with some clear packaging tape or duct tape to block water and drafts from getting into the home until a professional can come out and fix the window. It also acts as a barrier, deterring any intruders to gain access into your home. If the gap between the window and the door is significant, you may prefer an alarm system that has a window. This will provide the best of both.

2. Sagging

Upvc is a long-lasting and energy efficient alternative to timber sash windows. In time, they could develop a variety of issues, including sliding. A sagging window can cause problems with light, draughts or even security. If you find that your uPVC window is beginning to sag it's important to act quickly to stop the issue from worsening.

To repair a window that is sagging, you can try to reposition the hinges. First, Upvc Window Repairs you'll need to open the windows to get at the frame. Then, you can remove the top and bottom hinges using a screwdriver, and then adjust them counter-clockwise or clockwise. After you've repositioned the hinges, close your window and check for fitting. If you are happy with the fit of your window, you can tighten screws to hold them in place.

If you cannot reposition the hinges, you may need to replace the seal. Rubber seals can dry out and lose their elasticity over time, which causes them to loose their elasticity. It is crucial to replace your seal as soon as you can in order to ensure that your uPVC window watertight and draughtproof.

uPVC handles may also become loose. Often, this is caused by screws that have come loose over time. However, it could be due to the fact that the handle mechanism has been worn out. Fortunately, it's easy to repair the handle of a window that is loose yourself. You'll first need to close the window and do an initial fitting. The corner joints of the sash should align with the casing joint. If it isn't then you can use a screwdriver to loosen the handle and then reverse the mechanism back into its original position.

3. Water Leaks

It is crucial to take action if you get up each morning to discover mouldy walls and floors that are wet. Leaks of water from windows can cause structural damage to your home, and hinder your ability to control the temperature inside your home. The most common reason for leaks in uPVC windows is that the sealant around the frame is damaged or is missing.

This is a simple fix that can be accomplished by any DIYer who is competent. Based on the severity of the issue the old caulking may require removal before a new layer can be applied. It is important to keep in mind that when it is about uPVC window repairs, you should not be tempted to apply too much caulk and then make the area harder to clean and can reduce your energy efficiency.

Verify that the drainage holes have no debris in them and that the sill pan has been properly angled to allow the water to drain from the window. In more serious situations, you may have to replace the window.

Mold spots and rotten sills are other signs of water leakage. This fungus thrives under damp conditions and can spread quickly throughout the house.

If the leakage is occurring between the double-glazed glass it is more likely the problem is with the seal than the frame. It is also possible to be repaired by an uPVC window specialist who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

Hinges may be to blame if your uPVC window is difficult to open, or if it opens in the breeze. They can be easily repaired by any DIYer who is skilled and can usually be done within a few minutes.

Nearly every home in the UK will have either top hung or side-hung uPVC windows that use hinges and like any mechanical part they can wear down over time. It is very easy to replace a hinge on a window but it's much easier if someone else helps you hold the frame.

It is also important to ensure that the uPVC hinges are opened and closed in the right direction. Look for the arrows that are on each hinge to determine which direction the window doctor should be opened.

Faulty window hinges could be caused by improperly opening the window a certain way or by poor installation at the factory. It is usually possible to fix the issue by sending us a picture via our website and we will be more than happy to give you suggestions.

Regularly lubricating the hinges is also necessary. Applying a light engineering lubricant on the hinges is an ideal way to do this. We recommend using a lubricant that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication can allow the window operate and close more smoothly. It can also lower the risk of a window sticking and help prevent corrosion. This should be done at least every year. WD40 and other solvent based lubricants are not recommended as they can damage the parts of your uPVC window.

5. Draughts

Draughts in Upvc windows can be caused by a few different things. First, the hinges because of wear and tear, can become misaligned, this will cause an opening to appear between the sash and the frame. If they are beyond repair, it could be required to realign them. Second, the interlock can be disaligned. This is located on the hinge side and may need to be cleaned. In some cases it might be necessary to replace the hinges.

These seals can wear down or be damaged over time, allowing air to escape. Replacing these with high-quality weatherstripping is a good way to keep draughts at bay. Replace the windows made of upvc with low-emissivity glass. This will help control indoor temperatures and decrease the possibility of draughts.

Another method of reducing the amount of draughts is to use a draught-excluder. These are usually fabric tubes filled with a filler which can be put on top of your window sill. They can help stop cold air from entering and keep your home warm and cosy!

The windows made of upvc can remain a great source of insulation and security to your home by performing regular maintenance and repairs. It is crucial to recognise that all windows have a lifespan and they may reach the point when it's more cost-effective to replace them rather than repair them. If you encounter any issues with your Upvc window, it's best to consult a professional as soon as you can.