Reasons Your Fiat 500 Key Fob Won't Work

A key fob from fiat van keys 500 is a convenient method to unlock the doors and start the car. However, there are numerous reasons why the fob won't be functioning. This could be due to a dead battery, water damage, problems with the receiver modules, and interference.

This listing is for a NEW replacement program fiat 500 key fob Flip Key Remote that appears similar to the Ilco brand. It has to be professionally programmed (click here to find local automotive locksmiths). Includes lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason why your 500 key fob will not function is an inactive battery. Key fobs of today have limited operating range and must be within only a few inches from the vehicle to work. If you are far from your vehicle and you press the key fob button, the car won't respond and will display a "Key Fob Not Detected" message in the instrument cluster.

If this occurs then replace the battery for your coin-cell (Part Number CR2032) by a fresh one from a reputable brand such as Panasonic Duracell or Energizer. They are usually available at your local hardware store, or online.

You can test the battery on your coin-cell by pressing the buttons while standing close to your Fiat 500. The parking lights should flash and the key fob should operate the lock and unlock switch.

If your key fob doesn't work even after replacing the battery, it may be water damage that is preventing it from connecting to the module in your vehicle. Water damage can happen through a variety of methods, including simply splashing or submerging the key fob into saltwater at the beach. If you suspect that your fob was exposed to water, you can try placing it in a dry rice bag to pull the moisture out. If this isn't working, you'll need to have your fob reset by an auto locksmith or dealer.

Water Damage

Water damage can occur if you immerse the fob into the ocean, or wash it in a washer. Saltwater is especially dangerous to the circuit board of the fob, causing it to short out and eventually die. It's not a good idea to soak the fob in water but don't give up even if you accidentally drop the fob in water or fail to remove it from your pants pocket.

Remove the battery first. Before replacing the battery clean the electronic chip using isopropyl or similar products. Check the fob to check if it's functioning. If the key does not function, it may need to be reprogrammed. This is typically handled by a professional or dealer auto locksmith.

If the key is older and has not been programmed to your car It is likely that it needs to be replaced completely. This is a simple process that can be handled by a professional automotive locksmith. The locksmith will require the key to be cut to match your vehicle's ignition. They will also need to reprogram the fob for your vehicle's system. This is a fast and cost-effective procedure which can be completed within the same day.

Receiver Module Issues

One of the most common reasons why your 500 key fob might stop working is that it's simply out of range. The remote has a maximum range of 30 feet, so if you are too far from your vehicle it will not respond to your commands. This can be easily fixed by moving closer to your vehicle until it starts responding.

If your fob isn't working after replacing the battery for the coin, also known as a "button", "watch" or "button" or "button", it could be due to an issue with the internal circuit board. Reprogramming the fob typically resolves the issue. You can find instructions on how to do this for the majority of automobiles by searching YouTube or checking out the owner's manual.

It is sometimes necessary to replace the metal clips that hold the coin batteries in place. If they lose tension they could stop the battery from being seated properly and can cause your remote to malfunction.

In rare cases the fob could be disconnected from your vehicle due to software problems or hardware issues. You can fix this problem by visiting your local auto-locksmith or Fiat Van Keys dealer to reprogram your key fob. In some cases it is possible that the software will require reinstallation into your body control modules.

Interference

Interference can also cause the key fob to be unable to receive or transmit a signal. This could happen when the keyfob is in close proximity to a radio transmitter, such as a cell phone or radar detector. The key fob may not work due to a bad connection to the buttons or water damage, or damage to the internal chips.

If the key fob has failed to work one day suddenly or even after trying everything you can at home to solve it e.g. replacing batteries, reprogramming or fiat van Keys using the spare key fob, it could have a faulty receiver module on your 500. The receiver module, located under the dashboard, is able to pick up radio frequency signals from your key fob. It transforms the signals into electronic commands that are then interpreted by the vehicle.

Luckily, there is an easy method of resetting all of the on-board systems in your 500, including the key fob. Disconnect the battery for 15 minutes, removing first the negative cable, then the positive cable. Then reconnect the battery. This will get rid of any remaining electrical charge and restart the car's computer system, which can help you get your key fob working again. If the problem persists it is recommended that you consult an expert certified technician. They will be able to identify the root cause of any problems.