Reasons Your fiat 500x key fob programming panda key (try what he says) 500 Key Fob Won't Work

A key fob from fiat 500x key fob 500 is a convenient way to unlock the doors and start the car. There are a myriad of reasons why the fob won't be functioning. It could be due to a dead battery or damage to the receiver module, water issues, and interference.

This listing is for an NEW replacement fiat abarth key Flip Key Remote - look-alike Ilco brand that must be programmed professionally by a local locksmith (click here for Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most common reason your 500 key fob will not work is an inactive battery. Modern key fobs operate with a limited operating range, and must be within some feet of the vehicle to function. If you're not close to your vehicle, and you press the key fob button the car will not respond, and will display the "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the battery in the coin cell (Part number CR2032) with a brand new one from a trusted brand like Panasonic, Duracell, or Energizer. They are available at the local hardware store or online.

After you've replaced the coin cell battery, you can test it by standing close to your fiat ducato key fob replacement 500 and pressing the buttons. The parking lights should light up and the key fob will operate the lock and unlock switches.

If the key fob doesn't function after replacing the battery, it might be damaged by water that blocks it from communicating with the receiver module in your car. Water damage can happen in a number of ways, from the slightest splash to submerging the fob into salt water at the beach. If you think your fob was exposed to water, put it in a rice bag to draw out the moisture. If this fails, you'll need to have the fob reprogrammed either by an auto locksmith or dealer.

Water Damage

Damage to the water supply can occur if you immerse the fob into the ocean, or wash it in a machine. Saltwater can be particularly harmful to the circuit board of the fob which causes it to short out and eventually end up dying. Getting the fob wet is not a good idea but if you accidentally drop it into an empty cup of water, or do not remember to remove it from your pants pocket prior to running the washing machine Don't give up hope.

First, remove the battery from the fob. Clean the electronic chip using isopropyl alcohol or another similar product and then dry it completely before replacing the battery. Check the fob to verify if it's working. If the key still doesn't work, it may have to be changed. This is usually handled by an auto locksmith or dealer.

If your key is old and has not been programmed for your vehicle, you will need to replace it completely. This is a simple procedure which can be accomplished by a professional automotive locksmith. The locksmith will require the key cut to match your vehicle's ignition. They'll also need to reprogram the fob in your car's system. This is a quick and affordable process that is usually completed in the next day.

Receiver Module Issues

One of the main reasons why your 500 key fob might stop functioning is that it's out of range. The remote has a range of 30 feet, so if you are too far from your car it won't respond to your commands. This can easily be resolved by moving it closer to your vehicle until it begins responding.

If you've replaced the coin battery (commonly known as a "button" or "watch") and the fob won't work it could be due to an internal circuit board issue. In most cases, reprogramming the fob will resolve this issue. There are instructions on how to do this for all vehicles by searching YouTube or looking through the owner's manual.

It is possible to replace the metal clips that hold the coin battery in place. If they lose tension it could prevent the battery from being properly seated, and this will cause your remote to malfunction.

In rare cases the fob might be out of connection with your vehicle as a result of hardware or software problems. You can fix this problem by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain instances, the software may also need to be reinstalled in your body control modules.

Interference

Interference can also cause the key fob not to receive or transmit an signal. This may happen if the keyfob is in close proximity to a radio transmitter like a cellphone or radar detector. The key fob could not function because of a weak connection with the buttons, water damage or damage to the internal chips.

If your key fob suddenly stopped working, or if you have tried everything at home to fix it (e.g. You may have a faulty 500 receiver module after you've tried replacing the battery, reprogramming, and using an alternative key fob. The receiver module, which is located under the dashboard, is able to pick up radio frequency signals from your key fob. It converts them into electronic commands that the vehicle interprets.

There's a simple method to reset the 500's internal system including the keyfob. Disconnect the battery for 15 minutes by taking off first the negative cable, then the positive cable. Then, reconnect the battery. This will eliminate any residual electricity and restart the car's computers. This could allow you to get your key fob working again. If the issue continues you should speak with an expert technician. They can determine the root of your problem.