Cat flaps let your pet leave and come at their own pace without you needing to let him in or out. They can also help prevent your cat flap step from urinating in the home.

Installing a cat flap into a door panel made of Upvc is a lot easier than glass doors, however it does require some skills and the right tools.

Measure the Door

The installation of a cat flap in a front door can be difficult however, provided that the cat flap is of the correct one and you follow the directions it shouldn't be too difficult. We will demonstrate how to draw the shape using a jigsaw in order to cut out the door's opening. Then we will finish the job by affixing the flap. This will ensure that the flap stays in place and protects the door from rain and wind which can cause damage.

The first step is determine the width of your pet to get an accurate measurement of what size of cat flap you will require. This will ensure that the flap is large enough that your pet can enter and leave the house without having to open and close the door every time, but also small enough to keep the pet from straying too far in either direction.

Once you have the measurements you can mark out the location on the door where the template should be placed. usually, this is done using an X, however some kits come with an illustration that outlines where to drill, if you have one, then attach it to the door and draw a line around the door. If your door has moulding or sill on the bottom edge of it ensure that you have enough clearance from these as this will ensure your cat's safety and prevent them gaining access to your home.

Use a set square to check that you are cutting correctly and to make sure the hole is a good rectangle shape. When you are satisfied with this, you are able to start removing the remaining door material. If you have a set square then use it to ensure whether you're cutting in the right way and to ensure that the hole is a good rectangular shape. Once you are satisfied with this you can start to remove the rest of the door material.

Draw a Line

The cat flap is a great way to allow your pet to go out and in without having to worry about them being in the house with a visitor, or leaving unwanted gifts inside the house. It also reduces drafts and helps keep the temperature in your home in a stable manner. However, installing the cat flap to your door can seem like an intimidating task for those who have never done it before. This can lead many to hire a professional joiner or carpenter to do the job instead. This is an option but you can do it yourself if the tools are appropriate and the steps are followed.

This is much easier to accomplish on wooden doors, but it is possible with uPVC. However you should be cautious not to scratch the doors as this could cause the door to be damaged and invalidate your warranty. The first step in the process is to measure the door, ensuring that it is able to be able to accommodate the new cat flap. This should be simple enough when you have the standard uPVC door, however you may need to take more care if you have an alternative type of door since these can be more difficult to cut into than solid uPVC panels.

The next step is to determine the belly height of your cat. This is the amount of height between the floor and the underside of your cat's stomach. You'll need to locate an area on the door that will allow your pet to pass through wall cat flap comfortably. Once you've got the information, you'll need to mark the area with a spirit-level and a pencil so you are certain that the hole will be suitable for your cat Flap in upvc door panel.

After you've marked the area, you're now ready to cut the hole. You will require the jigsaw, and it is important that you take your time to ensure that the cuts are smooth and clean, rather than uneven and rough, since this could damage your door. Wear safety glasses and a dust mask when using the Jigsaw. Inhaling sawdust is hazardous for your health. After you've completed the cutting process, you will need to smooth out the edges of the hole with sandpaper, so that your cat flap can be fitted easily.

Make a hole

It can be a challenge to fit the cat flap onto a door panel or sealed double glazing unit. You might be tempted to tackle the job yourself, but unless have plenty of experience with DIY, it's recommended to hire an expert to complete the job for you. A mistake in the process may not only be unsightly but also an issue for security and also allow cold air to get in when the cat is outside, and hot air to escape inside.

The first thing you have to do is mark out the location of the hole in the door using a pencil and a spirit level. This will ensure that it is correctly placed and runs in a straight line with the other parts of the door. Make sure to have sandpaper to smooth any rough edges.

Once the line has been marked you should cut out the hole with the jigsaw. Remember to wear any safety gear for working with the power tool. If you are concerned about the sound produced by the jigsaw, you can purchase an electric version that is quieter and simpler to use.

It is important that you only remove the material required to make the cat flap. A small amount of material will be needed to cover the thickness of the wall of the cat flap itself but removing more than this can cause problems or damage the doors frame.

A door made of upvc may contain a metal frame or panel which could block the microchip cat flap, and if this is the case you'll need to cut an oversize hole so that the metal does not come into contact with the wall of the cat flap, if this is done, it is important to fill in the gap and make it watertight.

If you're installing an animal flap to a upvc door or double-glazed window with a frame made of metal, you'll need to talk to a professional who will provide you with a brand new glass pane with the hole for the cat flap premade inside. It will be much cheaper to have this done than trying to fix the cat flap onto an existing glass pane that has not been manufactured specifically for this purpose.

Install the Flap

cat flap installation in glass doors near me flaps let your pet move around as they please, giving them the ability to unwind in the home whenever they're feeling like it. However, if you have a uPVC door, it might be difficult to fit an animal flap, especially if you don't own glass cat flap installation near me panes that can be cut to fit one. Luckily, if you're happy to purchase and install a replacement half-glazed uPVC panel, it's possible to fit a cat flap to the doors. It's not as simple as just cutting a hole through the door however, and there are some things you'll need to take care of first to make sure it's safe.

A composite, uPVC or GRP door panel is usually comprised of a thin plastic skin that is bonded to an insulating polystyrene core. It is important to be careful when cutting the material. This kind of door comes with a template that you can use to make the hole.

After you've marked the position of the hole in your door, it's time to fit the cat flap itself. You can choose from a variety of models, ranging from simple push-button units to microchip-activated ones that only let your pet in. Whatever type of cat flaps you choose, it's vital that your cat is able to utilize the flap with ease without getting stuck outside in the rain.

A circular fitting is superior than a square one, as circles can be cut more securely into glass. This is because square holes make glass more vulnerable to cracking when drills are used on it. This is also a safer option since you don't have to drill into the toughened glass, which could break and cause harm to your pet or family. This is especially important if there are children or elderly people in your home that could be injured by glass shards.