How to Replace the Replacement Key Battery For the Saab 9-3

Saab owners have to follow a series of special steps to install an additional ignition key. It requires dealer assistance using an electronic handheld computer called Tech-2. Then it is necessary to purchase a new transponder. key need to be purchased.

Make sure to rotate your keys in order to prevent one from wearing out quicker than the next. This will help keep your keys in good condition.

Replacement Case

The new key fobs are not like the older Saab key fob repair keys. They feature electronic components which make it hard to copy. That has made car theft much more difficult than it was just a few years ago. However, it has also made replacing lost keys a more expensive task.

Every owner of a Saab 9-3 must have at least two working keys. It's expensive to replace a lost key as it requires replacing the CIM module, and programming the locking cylinders. Dealers will typically charge $100-$200 to complete this.

There are ways to reduce these costly costs. Some parts retailers will look up the code from an old key (usually the same one that opens the doors and turns the ignition) and cut a brand new key blade from metal for just a fraction of dealer cost. The key, however, must be the same as the original one in order to function within your car.

Follow these steps to replace the case. You'll need a flathead screwdriver along with some patience. With the screwdriver, pry away the plastic and take out the emergency key. When the case is opened take the electronics out and put them in the new case. Make sure you insert the correct key and badge inside the case.

Replacement Battery

The Saab 9-3 replacement battery is a cheap component that can be quickly and easily replaced. This DIY video from YouTube Cyclone Cyd shows how to replace the battery for the remote key fob in just four steps. This tutorial can be used with any modern Saab key fob. However, the process may differ slightly.

The button is normally located next to the Saab logo on the back of the fob. This button is typically located on the back of your fob, just below the Saab Logo. Next, use an screwdriver with a flat head to insert into the small hole of this button. This should be sufficient to allow you to open the fob case to allow you to change the battery.

Once the new CR1632 battery is in place then you can reassemble your remote key fob. You can then program it to your car. The entire process should not take more than a half hour at the most. It's a very easy process that does not require any special tools.

If you lose your key, the procedure will be a bit more involved, but it can still be done. The dealer must determine the VIN of the car and then request a replacement key blade and TWICE module, both with the exact unique code. After that, they will be required to cut the replacement key and then program it using a brand new tool for programming called MDI.

Replacement Key Fob

The key fob is equipped with batteries that are used to lock and unlock your vehicle. They have a limited life span and will eventually die. This is a typical issue that happens with all cars and the good news is that you can replace the batteries on most fobs, without replacing the entire case. Amazon sells replacement fobs that already have all the electronics installed. You can simply remove the case and replace the batteries. It is important to keep in mind that you'll need remove the emergency key first, and you can do this by putting the screwdriver of a small flathead into the slot in the middle of the case. The case will split once you turn the screwdriver around it.

When you are ready to replace your keys, make sure you have a spare as this will reduce the total cost by a substantial amount. If you do have a spare, you can have the dealer cut an entirely new key and then program it to the car, which is cheaper than replacing the whole key fob.

If you do not have a spare key car key, you can add a second key to your car, but it requires a lot of research and effort. The cost for adding a second key is several hundred dollars and also requires programming of the car's computer. This can be accomplished by a professional, but it is an expensive option for most owners.

Replacement Ignition

Unlike the earlier Saab vehicles, the latest SAAB 9-3 models are equipped with an extremely sophisticated alarm system that is built on a key code. If you lose only one key, it may be expensive to add another one since the car needs to include a computer and also be programmed to accept a brand new key. Even a dealer can charge hundreds of dollars to program a new key in the event that they are unable to complete the task.

If you've lost your only working key and a dealer is able to replace the computer in your car (known as the CIM or saab key code TWICE) to create a replacement, and will charge top dollar for it. We can reprogramme the existing EEPROM inside your car's computer to be ready for an additional key. This will save you more than 50% on what you would have to pay the dealer.

If you've been a long time owner of an 03-11 SAAB 9-3, then you likely have noticed that the ignition switch isn't really all that robust. If the ignition key you have isn't working correctly, you should think about replacing it. They can become extremely sticky and the buttons have been known to fall off. It's not so difficult as it may seem to replace the ignition key. With the proper tools, it can be accomplished quickly.